Version2.1.4.0
<Improvement>
- Supports for settings for [Each inspection machine] on the [RESULT OUT] tab of the General Setting

<Arrangement>
- Added [Synchronize timing of result text output of dual machine] in [Save Inspection Information RC22X format] tab of the General Setting

<Corrections>
- Added the function to restore registered addresses, ports, and PC names from backups when address settings are lost
- Fixed cell image saving process
- Changed so that the capacity of the destination disk is checked at startup, and if there is insufficient disk capacity, inspections cannot be performed until the capacity problem is resolved
- Changed so that the connection with the inspection machine cannot be established when data cannot be saved in the DB

Version2.1.1.6
<Improvement>
- Deal with the special order

<Arrangement>
- [NG of BlockMark makes judgement of XML output OK] option is added to XML tab

<Corrections>
- Fixed a problem in which the panel judgment result was output to the block judgment result when outputting RS232
- Fixed a problem to cause DB write error when using Combination setting
- Fixed a problem with certain Windows 11 PCs displaying an error when disconnecting the inspection machine
- Fixed a problem where receiving inspection results at the time of the change to the next month would cause an error - - and prevent connection to the inspection machine
- Fixed formatting errors in XML3
- Modified to limit communication connection with inspection machine in case of DB error
- Fixed to restore previous Address settings when the settings are lost
- Added software version information to XML output content

Version2.1.0.0
<Arrangement>
- Standardized the application for the full version and the trial version
- Changed so that the PCB barcode and results are sorted by block number for XML output
- Added iTac MachineMDE
- Added [MachineOUT is sent only once(pcb send only] Option

<Correction>
- Fixted a problem in long board inspection where information on long boards was not reset when the [Send Cell Image] setting was OFF

Version2.0.0.1
<Improvements>
- Supports Bottom 3D Inspection Machine
- Supports PostgreSQL Version15

Version1.4.2.1
<Improvements>
- Added automatic export function

<Arrangement>
- Changed Log output function to fixed ON

<Correction>
- Fixed a crash that could occur when displaying error messages received from the inspection machine
- Improved connection with the inspection machine

Version1.4.1.8
<Correction>
- Fixed the problem that the address settings for 10 machines were not displayed in the 10 machines option when using remote desktop connection.
- Fixed a problem in XML output that </packs_no> was output as </lacks_no> after 1.4.1.1

Version1.4.1.6
<Improvement>
- Addition of CSV output
- Addition of option [NG of BlockMark is judged as OK] for CSV output
- Addition of option [PCB without barcodes are not output as files] for CSV output

<Arrangement>
- Changed so that A1, A2 (B1, B2) data are merged and output in XML output of Long Board
- The number of Ref.Des. data saved in the DB is now 64 bits

<Correction>
- Fixed a problem in XML output of Long Boards that the end tag </error_no> was not output
- Long Board inspection is now compatible with the setting [Send Cell images (CS-Center only)] off

Version1.4.1.0
<Arrangement>
- Added [File Path Setting] to switch between [File per panel] and [File per PCB] for XML output settings.

<Correction>
- Fixed a problem which an error occurred when opening the [Setting for Dual inspection] in the [Address Setting] under connecting 10 machines, which is an additional option.

Version1.4.0.8
<Arrangement>
- Added option to output the number of NGs after confirming G/NG in error_conf of XML
- Changed to set default values for unset points when reading NGID setting files

<Correction>
- Improvement of memory leak problem when connecting multiple machines
- Improvement of application crashing when connecting multiple machines

Version1.4.0.4
<Improvement>
- Deal with the special order

<Correction>
- Fixed a problem that may cause a DB save error when inspecting with multiple machines at the beginning of the month
- Added option to switch serial number/block number to PCB number in XML output function
- Fixed 1D barcode decoding process for HALCON13

Version1.4.0.0
<Improvement>
- Supports up to 256 NG-IDs (0-255)
- The size of an inspection frame is added on the result exported on [Save inspection information to file]
- Help button is added on DB message displayed on the screen
- Deal with the special order

<Arrangement>
- Remote operation screen is modified
- Changed [Side cameras for NG direction in Pack are highlighted] to [Views for NG direction in Pack and view45 be noticeable]
- Changed [Display NG direction in 4 views] to [Show only NG direction in 4 views]

<Correction>
- Deal with the special order

Version1.3.0.0
<Improvement>
- [Enable barcode add-in] option is now compatible with HALCON 13.0

<Correction>
- Deal with the special order
- [ErrorPixelFormat] or [Er_2_3] occurred and displayed while connecting with 22X
- Fixed the problem that [Barcode is made PCB name -side-Lot-inspection number.] option did not work
- fixed memory leak
- Corrected aspect ratio of side screen
- Changed the specification to display an error when saving inspection information in DB fails
- HASP driver update v7.81-> v8.13

Version 1.2.5.7 to 1.2.7.4
<Improvement>
Add a function to quit the software without displaying confirmation message.
[Barcode completion] function is added on [General Settings].
Add a function to delete inspection data on DB by month.
Add Angular camera image saving function while exporting inspection data to XML.

<Arrangement>
Change a default log export folder while exporting a log : C:Marantz\CsCenLog
Add barcode information to NG data file name on inspection data export function to XML.
Add an information of PCB side (A or B) on inspection data export function to CSV.

Version 1.2.5.6 2019/05/28
	Corresponds to the full screen of AOI.

Version 1.2.5.5 2019/05/15
	Fix: Output of XML may not save NG image for saving information.

Version 1.2.5.4 2019/04/25
	Add "Data without barcode is not output to XML".
	Modified the "CustomFunction" 2(for exclusive customer).

Version 1.2.5.3 2019/04/12
	Modified the "CustomFunction"(for exclusive customer).
	Add "Client".

Version 1.2.5.2 2019/02/05
	Add "Delete by month".

Version 1.2.5.1 2019/01/29
	RS232C output is compatible with barcode reception.

Version 1.2.5.0 2018/12/19
	"RS232C" was added to "Setting".
	"DB not used" was added to "Status monitor" of "Setting".
	Modified the inspection time(for exclusive customer "a").
	Modified the output(for exclusive customer "a").

Version 1.2.4.9 2018/09/10
	Folder of "Disk Warning" is automatically entered.
	warning is displayed when the HDD capacity is 500 G or more.

Version 1.2.4.8 2018/08/24
	Modified the function of "C"(for exclusive customer).

Version 1.2.4.7 2018/08/10
	Add function of "L"(for exclusive customer).
	Add function of "i"(for exclusive customer).
	Defect image is deleted in 0113.

Version 1.2.4.6 2018/07/26
	Modified it because the cell image was only partially saved.(for exclusive customer "C").

Version 1.2.4.5 2018/07/05
	Hasp recognition on the remote desktop was slow, so fix it.

Version 1.2.4.4 2018/06/08
	Changed to be error if "\" is found in data matrix.

Version 1.2.4.3 2018/05/10
	Modified the characters in the delete dialog.

Version 1.2.4.2 2018/04/13
	Erroe 103 appears when switching logs, so I corrected it.
	Add function of "A"(for exclusive customer).

Version 1.2.4.1 2018/04/05
	Changed not to output XML when there is no combined data.
	Changed to output combined XML even for connections that do not send cell images.

Version 1.2.4.0 2018/03/29
	Add function of "C"(for exclusive customer).

Version 1.2.3.9 2018/03/12
	The function to prevent the same date and time data from being saved was fix because it was reset when disconnecting the connection.

Version 1.2.3.8 2018/03/07
	In D22X model, PC name of XML output was modified to use for display.

Version 1.2.3.7 2018/03/05
	Add function of "Q"(for exclusive customer).

Version 1.2.3.6 2018/02/16
	Fix not to save data with the same time.

Version 1.2.3.5 2018/01/29
	Changed English.
	Add function of "Combination setting".

Version 1.2.3.4 2018/01/05
	Fix the error occurred when reading setting. 12/25
	Add function of "Nexim". 12/25

Version 1.2.3.3 2017/10/25
	Add function of "Mika"(for exclusive customer). 10/25
	I tried to work with non-administrator. 10/23

Version 1.2.3.2 2017/09/05
	Move XML output after saving to temporary folder.

Version 1.2.3.1 2017/06/26
	Countermeasure against different image from angular cameras.

Version 1.2.3.0 2017/04/20
	Make one piece of data with the same output position (for exclusive customer)

Version 1.2.2.9 2017/04/13
	Add the function "Confirm all NG Stamps inside the Pack" in Side camera tab at Settings menu.
	Add the function "Activate Good button only when confiming all" in Side camera tab at Settings menu.

Version 1.2.2.8 2017/03/23
	Fix the connect in D22X model

Version 1.2.2.7 2017/03/13
	Fix the available capacity of DB when saving picture number exceeded 1 million

Version 1.2.2.6 2017/03/06
	Fix the setting failure of CsWatch in D22X model
	Compatible to 5M camera
	Compatible to hasp_windows.dll

Version 1.2.2.5 2017/02/03
	Fix the output format of "XML3"
	Add the output function of OCR (for exclusive customer)

Version 1.2.2.4 2016/12/06
	Add function to create pcbinfo table.

Version 1.2.2.3 2016/11/29
	Fix the incorrect value of space left on DB.

Version 1.2.2.2 2016/11/15
	Add function of "Reference Designator without ( ) and [ ]".
	Add "Status_PCB" to XML output.

Version 1.2.2.1 2016/11/07
	Add OCR output.  (for exclusive customer)

Version 1.2.2.0 2016/10/17
	Fix "send server".  (for exclusive customer)

Version 1.2.1.9 2016/10/11
	Add function of "Inspection result output".  (for exclusive customer)

Version 1.2.1.8 2016/10/03
	Update the function to output "Result preservation" with both NG and OK result.  (for exclusive customer)

Version 1.2.1.7 2016/09/26
	Add function of "A block mark is not output" for XML output

Version 1.2.1.6 2016/08/31
	Add XML3 output

Version 1.2.1.5 2016/08/19
	Add function of "Result preservation" for custom order
	Update to save the last NG picture 08/18
	Image from angular cameras are deleted with Delete function 07/21
	Fix the DB value of free capacity displayed larger than real value 07/14
	Corrected the word from "Startting" to "Starting" at starting window 07/11

Version 1.2.1.4 2016/06/27
	Add "Output OK result" to XML output.

Version 1.2.1.3 2016/06/24
	Add function to customize PC name shown in Status Monitor.

Version 1.2.1.2
	Send back 0120 when CS-Center received 1234 from 22X(2016/06/16)
	* Disabled to connect in Catch mode when 22X is not adaptable to
earlier Catch system

Version 1.2.1.1 2016/06/13
	Bug fix for different file name at Symbol totals (for exclusive
customer)(2016/06/13)

Version 1.2.1.0 2016/06/09
	XML: Error message will be displayed if communication fails via HTTP

Version 1.2.0.9 2016/05/31
	Add MicroQR RemoveNoise(2016/05/31)
	Add log and changed the process when there is no file (for exclusive
customer)(2016/05/31)

Version 1.2.0.8
	Add Stop saving data when free disk space less than (Disk)
	Do not count same NG pictures in the alert for NG pictures saving
numbers

Version 1.2.0.7
	Fix sort function in plate output (for exclusive customer)(2016/04/27)
	Output the title line in plate output (for exclusive customer)(2016/04/26)
	Compliant to SpiderEye(2016/04/21)

Version 1.2.0.6 2016/04/15
	Stop with disk alert of less free disk space.  Disconnect when
stopped(2016/04/15)
	Add file switching function in Symbol totals (for exclusive
customer)(2016/04/13)

Version 1.2.0.5 2016/04/12
	Add the function not to display click control during G/NG
confirmation mode(2016/04/12)
	Possible to click both OK and NG while click control is activated(2016/04/07)

Version 1.2.0.4 2016/03/30
	Prevent the continuous click of remote function
	Display alert message when the number of NG pictures and the number
of file saved is different

Version 1.2.0.3 2016/03/17
	Add inspection log(for exclusive customer)
	Display higher-level communication error message in Send Server(for exclusive customer)
	Packs become "-" when Review output is from left to right

Version 1.2.0.2 2016/03/09
	Consider DB free capacity for free capacity checking warning (2016/03/04)
	Add plate inspection in symbol totals(for exclusive customer) (2016/03/09)

Version 1.2.0.1 2016/02/10
	Add function to save inspection log (for exclusive customer)

Version 1.2.0.0 2016/01/29
	Change "error_conf" of XML to 0(2016/01/29)
	Refer the PCB information in Review output (2016/01/28)

Version 1.1.9.9 2016/01/21
	Do not output old data if there are same barcodes in symbol totals(for exclusive customer) (2016/01/18)
	Add inspection log (for exclusive customer) (2016/01/19)
	Do not check folder if PostgreSQL is located in another PC (2016/01/21)

Version 1.1.9.8 2015/12/18
	New option for XML Pin Pkg

Version 1.1.9.7 2015/11/25
	Compatible to 4M size

Version 1.1.9.6 2015/11/12
	Add symbol total punching output
	There is no lot of symbol total while do not send cell image mode

Version 1.1.9.5 2015/10/06
	Add symbol total
	Add Send Server2(R)

Version 1.1.9.4 2015/09/15
	Add "inspection information saving"

Version 1.1.9.3 2015/08/26
	Change the string length 33 to 20 and more in "Special setting 1"(2015/08/26)
	Add contentType to "Send the XML to HTTP server"(2015/08/18)
	Add "Special setting 1" as addin

Version 1.1.9.2 2015/07/17
	"Send to HTTP server" add in XML

Version 1.1.9.1 2015/07/10
	Connection while log outputting may become the error.

Version 1.1.9.0 2015/06/25
	Make the XML judgment panellized PCB to judgment panellized PCB not a sheet judgment

Version 1.1.8.9 2015/06/24
	Check the XML folder five times at startup

Version 1.1.8.9 2015/06/03
	Check the existent of PostgreSQL and XML folder at startup

Version 1.1.8.8 2015/05/22
	New option for status monitor not to use TTL of AOI
	This is active on default

Version 1.1.8.7 2015/02/19
	Do not erase empty space when saving barcode

Version 1.1.8.6 2015/02/09
	Send Server function as addin
	Barcode out was code UTF

Version 1.1.8.5 2014/12/10
	Output Lot num too in XML

Version 1.1.8.4 2014/11/11
	Send Server in Addin menu
	Screen for FHD

Version 1.1.8.3 2014/10/02
	Error when month has changed while operation

Version 1.1.8.2 2014/09/19
	Crash when WIT information existed after Note at outputting XML

Version 1.1.8.1 2014/08/19
	Do not cut trace server (custom setting for exclusive customer)

Version 1.1.8.0 2014/08/18
	Bug fix, bad address
	Treat special letters &<>'" in XML
	/ was sent twice in remote controlling side camera view

Version 1.1.7.9 2014/07/11
	Show db empty space in settings

Version 1.1.7.8 2014/07/04
	Changed some custom made spec
	Send UUID when sending barcode decoding for connection with 22X (V150)
	Button position for FHD changed
	XML did not output block information when too many NG

Version 1.1.7.7 2014/06/17
	DB Password possible to set
	Receiving 16 when trace server correctly responds

Version 1.1.7.6 2014/04/30
	Addin tab

Version 1.1.7.5 2014/02/03
	Do not start on PC more than 596 hours running
	Do not show errors in front of the other software
	Do not show multiple errors

Version 1.1.7.4 2013/12/06
	Treat view45 stamp without specifying the direction to show

Version 1.1.7.3 2013/07/31
	New option not to count BlockMark NG in status monitor

Version 1.1.7.2 2013/07/08
	Module size and resolution options for MicoQR settings

Version 1.1.7.1 2013/06/20
	Wait for 70 sec at PC startup and retry 5 times if SPI is connected
	Reset Review and SPI when confirming empty disk space
	Do not delete Map View by delete function
	Delete MzMsg of CKD
	Couldn't quit software when Mics transfer failed

Version 1.1.7.0 2013/05/17
	Inspection stopped when resting SPI if there was mass SPI data

Version 1.1.6.9 2013/04/02
	Compatible to WIT's multi NG function

Version 1.1.6.8 2013/04/02
	Block number be barcode when Block PCB had no barcode
	Password for opening General Settings

Version 1.1.6.7 2013/3/18
	4 views in angular camera screen
	Keep direction of view45 stamp for angular camera

Version 1.1.6.6 2012/12/21
	When Block barcode had more than 10 digit, space was inserted at head

Version 1.1.6.5 2012/12/07
	Jpeg Error#53 bug
	Bad Address by pressing / while showing angular camera views

Version 1.1.6.4 2012/10/22
	Receive the New Map when updated

Version 1.1.6.2 2012/09/21
	Improved the speed for deletion of V1.1.6.1

Version 1.1.6.1 2012/09/20
	Bug for 1.1.5.7, all NG pictures were deleted

Version 1.1.6.0 2012/09/04
	operator name add for data export

Version 1.1.5.9 2012/08/09
	operator_ID tag add for XML

Version 1.1.5.8 2012/06/25
	Incorrect window_no in XML output if Block was not sequence
	Common Ng-ID

Version 1.1.5.7 2012/04/26
	NG pictures weren't deleted

Version 1.1.5.6 2012/04/20
	Bug unable to export .ini file
	Show warning when changing Review image folder
	Show warning when logoutput unable

Version 1.1.5.5 2012/04/10
	Faster data acquisition via network
	Faster image saving in DB
	Max. decoding timeout 3.5 sec for barcode
	DB IP and time add in Log

Version 1.1.5.4 2012/03/28
	Error44 when date wasn't input at deleting data
	Show warniing when DB IP not set
	Faster image saving
	Update XML2
	XML output incorrect when Block No.1 didn't exist

Version 1.1.5.3 2012/02/29
	Memory leakage at QR code Decode
	Speed up to save NG pictures

Version 1.1.5.2 2012/02/20
	Load meter add

Version 1.1.5.1 2012/02/16
	Valor XML PCB block no wasn't generated if block had no barcode
	New Option not to save data when empty disk space less than 100MB
	Compatible to FDL size

Version 1.1.5.0 2012/01/23
	Memory leakage when saving side camera image was off, but sent from AOI 

Version 1.1.4.9 2012/01/12
	New Option "Do not receive warning message on AOI"

Version 1.1.4.8 2011/12/06
	repaired tag add in XML output
	Operator ID for XML2, Operator ID Edit for XML2 (for Hitachi)
	Deleted un-used function "Send finish signal"

Version 1.1.4.7 2011/11/28
	Enable to handle MicroQR (with additional cost)

Version 1.1.4.6 2011/11/10
	MEK logo
Version 1.1.4.6 2011/11/01
	Respond to 22X when barcode decode error "!readError"

Version 1.1.4.5 2011/10/25
	Bug memory leakage on Win7
	Improved the speed to delete data
	Improved when deleting data there is no response.
	Add a window to show the number of recode when executing delete data, and possible to cancel.

Version 1.1.4.4 2011/09/30
	Treatment for crash (do not divid when 0)

Version 1.1.4.3 2011/09/20
	Could not send barcode number completely when more than 10 digit in FTP2 setting

Version 1.1.4.2 2011/08/24
	Button picture disappears by disabling desktop thema
	Fail to delete data sometimes
	Timer to prevent continuous mouse click
	Output log enables from general settings menu

Version 1.1.4.1 2011/08/08
	Bug that USER object increasing for reconnection (crash)

Version 1.1.4.0 2011/08/02
	Message change for FTP error
	Cumulative working hour, cycle time for XML2 change

Version 1.1.3.13 2011/07/26
	Revised recipt number to be 4 digit for FTP2
Version 1.1.3.12 2011/07/22
	New option in menu to show Status Monitor for the result of A+B side, requires unique barcode.
	Map View not updated because of incorrect sbpglib10.dll
	DB Manager Export/Import malfunction on Windows 7 -> Ver1.0.16

Version 1.1.3.11 2011/06/22
	Don't load SPI while DB warmup
	Save CKD Error file separately

Version 1.1.3.10 2011/06/16
	Enable CKD Pg6's long text
	Changed not to terminate by CKD file loading error

Version 1.1.3.9 2011/06/09
	Error when SPI reset

Version 1.1.3.8 2011/06/03
	Add Xml2

Version 1.1.3.7 2011/06/01
	Error by SPI reset
	Setting not inherited after update
	Couldn't release SPI when SPI folder didn't exist and quit
	software with error message
	Unnecessary file saved when only XmlImage is on

Version 1.1.3.6 2011/05/12
	Bug that Status Monitor showed wrong number when panellized PCB
	Improved speed to get panellized PCB info
	Changed time out for decoding barcode
	Bug when saving CKD data

Version 1.1.3.5 2011/04/26
	Add barcode output to log file

Version 1.1.3.4 2011/03/25
	Enable to switch language from UI

Version 1.1.3.3 2010/12/10
	Bug image taken by CaptureStamp causes JPEG error#53
	Localize

Version 1.1.3.2 2010/10/25
	Input error with Angle Camera files

Version 1.1.3.1 2010/10/15
	AOI Operator
	Save angular camera image after moving
	Help for Windows7
	New Installer

Version 1.1.3.0 2010/09/14
	Enable to use with multiple monitor
	Changed DB selection menu layout
	Save side camera images
	Enlarge + mark on side camera image

Version 1.1.2.9 2010/06/24
	Work without PostgreSQL

Version 1.1.2.8 2010/06/09
	Time to confirm line-cut set to be 80 sec.

Version 1.1.2.7 2010/04/05
	Do not count up when "Send Good data" is not checked on 22X,
	also incorrect headder info is attached.
	Improved it to be saved in Center.

Version 1.1.2.6 2010/03/26
	When no data is set to be saved, Port is not opened.
	Wait for PostgreSQl startup when CsCenter is set to start-up.

Version 1.1.2.5 2010/03/16
	Do not save NG blocks by BlockMark
	Not working other than 4 letters of machine name DJTECH

Version 1.1.2.4 2010/03/03
	Display _ when storing Wit data
	New option for Wit, not to output OK
	Bug-fix below 5 check-box did not work

Version 1.1.2.3 2010/01/22
	Do not stop loading when CKD file not found
	Lock error fix (Socket.RemoteAddres stops when exception)
	Warm-up add
	Timer Reset signal send to 22x when re-connect
	Do not try connecting while warm-up

Version 1.1.2.2 2010/01/05
	Display error message when CKD file not found

Version 1.1.2.1 2009/12/25
	Display error message when CKD file not found

Version 1.1.2.0 2009/12/15
	Data from Djtech is collected in directory per day
	Connection reset add
	New icon
	Side info displayed in information

Version 1.1.1.11 2009/12/09
	Enable log changed Shift+Ctrl to Shift only
	Progress bar for automatic deletion
	Show PC name when error to store data in DB
	No error should be displayed when no deleting data
	Delete MzMsg only when CKD deletion was succeeded
	Show message when port could not be opened.
	Use self folder when Log APPDATA not found.

Version 1.1.1.10 2009/11/10
	Data transmission not complete if IP of Mac was changed while connecting
	Disconnect if host name does not reach after receiving IP
	Screen update improved

Version 1.1.1.9 2009/11/05
	QRDecode Access violation when too many decoding request

Version 1.1.1.8 2009/11/02
	Access violation error to close window while decoding

Version 1.1.1.7 2009/10/23
	server resource deleted

Version 1.1.1.6 2009/10/22
	LAN Connection improved
	Sound for G/NG confirmation mode incorrect

Version 1.1.1.5 2009/10/16
	CPU becomes busy when cutting connection from AOI

Version 1.1.1.4 2009/10/15
	Output error log
	Improved loosing conenction
	Window like freezing when more than 3 AOI are connecting
	Check was not activated for Review
	Operation button for 22X was not pictured.

Version 1.1.1.3 2009/09/04
	Handle increases when checking Hasp

Version 1.1.1.2 2009/08/05
	Improved reconnection procedure.

Version 1.1.1.1 2009/07/14
	To be side B if Ckd *.pgm or DJtech is side B

Version 1.1.1.0 2009/07/14
	Improved loosing LAN connection
	XML "<!DOCTYPE..." deleted
	To be side B if PCB name has _B for SPI data

Version 1.1.0.9 2009/06/02
	Saving date should be different
	Waiting when receiving data from NGCV
	Enable more than 255 results
	Symbol had barcode

Version 1.1.0.8 2009/05/27
	NG rate shown as status
	AM/PM hides something

Version 1.1.0.7 2009/05/20
	Enable more than 255 results
	Enable more than 10 panels

Version 1.1.0.6 2009/05/19
	If no panel when count per panel option was on, display did not move forward/backward
	Wait until saving to display JPEG 

Version 1.1.0.5 2009/05/13
	Status display per panel

Version 1.1.0.4 2009/05/08
	Do not display connection error
	Start-up enabled
	Result did not have [1: when no barcode

Version 1.1.0.3 2009/04/30
	If result was OK in reviewer, data was not saved
	LAn speed improved
	Title of error dialog incorrect.

Version 1.1.0.2 2009/04/13
	SPI can connect 10
	Setting Save, loading add
	XML V4 terminated, V6 improved

Version 1.1.0.1 2009/03/25
	Bug to save DJTECH data twice
	packs_no was not exported to XML V6

Version 1.1.0.0 2009/03/19
	Released as V1.1
Version 1.0.1.5 2009/03/17
	Start in external display

Version 1.0.1.4 2009/03/11
	Watch does not show PCB name from SPI

Version 1.0.1.3 2009/03/05
	DJTECH dimentions x 10, to be same as CKD

Version 1.0.1.2 2009/02/19
	Prevent freeze while deleting
	Add date in About..for trial version
	Auto deleting add
	Send terminate signal

Version 1.0.1.1 2009/02/18
	Add XML

Version 1.0.1.0 2009/02/06
	Bug:Default directory for Reviewer is same with In and OUT

Version 1.0.0.24 2009/01/21
	Bug: create barcode with PCB name + inspection number

Version 1.0.0.23
	Barcode generated from PCB+chekced
	Barcode generated from PCB name + log + xxxxxxx

Version 1.0.0.22 2008/12/12
	Image from reviewer not saved

Version 1.0.0.21 2008/12/11
	SPI digit to be compatible
	SPI double reading
	Read DJTECH title items (items can be changed)
	SPI reset then read

Version 1.0.0.20 2008/11/25
	Bug:unable to delete after exporting
	Bug:[//] not displayed when NG pic is less than 1
	Bug: Barcode IP is grey out
	Data output even specifying PC name as well as not specified
	Data output possible without PCB name
	Change SPI saving

Version 1.0.0.19 2008/11/21
	Encoding error when first line of NgId is null

Version 1.0.0.18 2008/11/20
	When barcode is not saved, temporary saved in CatchBarcodeReserve.txt,
	then send next time
	Change not to access barcode open mode

Version 1.0.0.17 2008/11/13
	Saving speed be faster

Version 1.0.0.16 2008/11/10
	Saving speed be faster (150 images in 8 sec to 1 sec)
	Add MA
	Add item in Export

Version 1.0.0.15 2008/10/20
	No button in simple mode
	Create Export menu

Version 1.0.0.14 2008/09/29
	Process too late, data dropping
	CsCen Ngid unicode

Version 1.0.0.13 2008/09/26
	SPI reset button add
	SPI check button add
	IPAddress for barcode out

Version 1.0.0.12 2008/08/01
	Set directory to save Ngid
	No directory for Ngid
	Bug: Send to Watch dead
	Protect bug by Sidechar to be #0

Version 1.0.0.11 2008/07/29
	Barcode output Shared compatible

Version 1.0.0.10 2008/07/24
	Barcode output add

Version 1.0.0.9 2008/07/10
	Add OK Cancel in strings display
	If there is -, ref.des not shown correctly

Version 1.0.0.8 2008/06/02
	New Window while writing in DB
	NG pictures not saved to cut connection while saving
	NG pictures not saved if Window is closed while saving
	Traceability in Analyzer error if there is space after sym

Version 1.0.0.7 2008/05/26
	Directory path error

Version 1.0.0.6 2008/05/20
	ITF decoding error

Version 1.0.0.5 2008/05/20
	ITF and Code39 to be same

Version 1.0.0.4 2008/04/23
	pcb_id numbering for captured image

Version 1.0.0.1 2008/03/03
	Image shifting on HDL, RC button shifting